Axxess Interface Satellite Radio OESWC CLASS2H User Manual

INSTALLATION INSTRUCTIONS FOR PART OESWC-CLASS2H  
OESWC-CLASS2H  
03-UP CLASS2 HARNESS FOR OE RF/STK  
The OESWC-CLASS2H is to be used with either the OESWC-STK  
or OESWC-RF. Please refer to instructions provided with  
OESWC-STK or OESWC-RF for mounting instructions.  
1-800-221-0932  
axxessinterface.com  
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION  
 
5. This is the end of the auto detection stage. If the OESWC TRANSMITTER  
detected the vehicles radio successfully the led will light up solid red.  
6. Make sure the steering wheel control buttons function correctly in the vehicle  
and enjoy your radio.  
So what if the led does not light up solid red?  
Check out troubleshooting section below.  
Troubleshooting the Auto Detect Mode  
So you tried the auto detect feature and at the end the led did not stay on solid  
red, it started flashing. That means the OESWC TRANSMITTER did not detect  
the vehicles radio. Follow these couple steps to determine what happened:  
First some basic steps:  
1. Verify that you have 12 volt accessory and a good ground to the OESWC  
interface.  
2. Verify that the battery is good on the OESWC transmitter.  
3. Refer to the “Setting up the OESWC transmitter” section of this manual and  
repeat those steps.  
2
 
STALK  
Wiring of ASWCSTALK and interface  
1. Connect the BLACK wires of the ASWCSTALK and the BLACK wire of the  
interface to ground. You may use the same ground point that is used for the radio.  
2. Connect the GREEN/ORANGE and BLACK/GREEN wires of the  
ASWCSTALK to the corresponding wires on the interface.  
3. Connect the RED wire to 12 volt accessory  
4. Tap off all other unused wires on the interface.  
Programming the ASWCSTALK  
* If this is the first time the ASWCSTALK is being installed:  
1. Turn the ignition on; the led will start flashing rapidly which means the  
interface is looking for the ASWCSTALK and the radio. Go to step 3.  
OR  
* If the ASWCSTALK was installed before:  
1. Turn the ignition on, the led will flash slowly  
2. Hold down the reset button for more then 2 seconds but less then 10  
seconds, the led will start flashing rapidly  
3. The ASWCSTALK INTERFACE will automatically find the ASWCSTALK and radio.  
4. After a couple of seconds the led should stop flashing and not light up for 2  
seconds. At this point do not push any buttons.  
5. After the 2 seconds there will be a series of 7 flashes, some short and  
some long.  
6. The led will pause for another 2 seconds then flash up to 10 times.  
7. This is the end of the auto detection stage. If the ASWCSTALK interface  
detected the vehicle and the radio successfully the led will light up solid red.  
8. Make sure the steering wheel control buttons function correctly in the vehicle  
and enjoy your radio.  
3
 
If the ASWCSTALK is mounted on the right side of the steering column follow the  
instructions below. (Auto-detect must be done first)  
1. Turn the ignition on  
2. Press the MODE on the ASWCSTALK for 10 seconds  
3. Then press volume up for 2 seconds  
4. The ASWCSTALK is now configured for the right side  
Troubleshooting the Auto Detect Mode  
So you tried the auto detect feature and at the end the led did not stay on solid  
red, it started flashing, or the steering wheel controls did not function properly.  
That means the interface did not detect the ASWCSTALK or the proper radio.  
Follow these steps to determine what happened:  
First some basic tips:  
1. Verify that you have 12 volt accessory and a good ground to the  
ASWCSTALK and interface.  
Once all the information above has been verified and correct, you will need to  
put the interface back into auto-detect mode. Follow the instructions from “If the  
ASWCSTALK was installed before” section above, however this time take notice  
of the led flashes in steps 5 and 6.  
4
 
1
2
3
4
5
1. Volume up  
2. Volume down  
3. Seek up  
4. Seek down  
5. Mode (source)  
3
4
1
2
5
1. Volume up  
2. Volume down  
3. Seek up  
4. Seek down  
5. Mode (source)  
5
 
NOTES  
 
INSTALLATION INSTRUCTIONS FOR PART OESWC-CLASS2H  
KNOWLEDGE IS POWER  
Enhance your installation and fabrication skills by  
enrolling in the most recognized and respected  
mobile electronics school in our industry.  
800-354-6782 for more information and take steps  
toward a better tomorrow.  
Metra recommends MECP certified  
technicians  
1-800-221-0932  
axxessinterface.com  
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION  
 

3M Air Cleaner 963E User Manual
3M Oxygen Equipment AS 400LBC and AS 600LBC User Manual
ADC Network Card FlexWave User Manual
ADTRAN Switch 1224R User Manual
Amana Dishwasher W10254854A User Manual
Amana Microwave Oven AMC1070 User Manual
Atlona Home Theater Server AT AV0808N User Manual
Audiovox Speaker BP110 User Manual
Avocent Switch DSR2010 User Manual
Axis Communications Security Camera P5532 User Manual