Audiovox Satellite Radio XM RCV User Manual

®
ELECT RO N ICS CO RP.  
XM® SATELLITE DIGITAL AUDIO  
RECEIVER SYSTEM MODEL SRXM-001  
INSTALLATION MANUAL  
FOR USE WITH THE RADIO RECEIVER  
UNIT (RRU) MODEL XM-RCV  
For Custom er Service  
Visit Our W ebsite At  
WWW.audiovox.com  
Product Inform ation, Photos,  
FAQs O wners M anuals  
 
INSTALLATIONandWIRINGPRECAUTIONS  
1. To prevent a short-circuit, Be sure to turn off the ignition and remove the negative (-)  
battery cable, prior to installation. Connect power wires last.  
NOTE: If the SRXM-001 System is to be installed in a car that is equipped with an on-board  
drive or navigation computer, do not disconnect the battery cable. If the cable is discon-  
nected, the computer memory may be lost. Under these conditions, use extra caution during  
installation not to cause a short circuit.  
2. Do not install the unit in the following locations:  
Locations exposed to direct sunlight.  
Where hot air is discharged from the car heater.  
Inareassubjecttoextremetemperatures.  
3. Incorrectinstallationmaycausedamagetothesystem. Mounttheunitfirmlyinplace,using  
the supplied brackets and screws.  
4. Be careful not to damage the car wiring.  
5. Be sure to use the supplied screws and washers.  
6. Be careful not to snag any wires when tightening screws.  
3
 
PACKING LIST  
SRXM-001 MAIN SYSTEM COMPONENTS  
(NOTE: Components are not drawn to scale.)  
RADIORECEIVERUNIT(RRU)  
Model # XM-RCV  
SATELLITESYSTEMCONTROL  
UNIT(SCU)  
FM MODULATOR /  
CONTROL INTERFACE  
Model # SAT-COM  
1
4
7
2
5
8
0
3
6
9
AUDIO OX  
R E  
W
P O  
SFT  
AUDIO OX  
AUDIO OUT  
TER.  
SAT.  
R
L
DIN OUT  
1 pc.  
(P/O SAT-COM)  
1 pc.  
1 pc.  
INSTALLATION PARTS  
Self-tapping Screws (5mm x 15mm), with  
Flat Washers and Lock Washers  
(Used to mount RRU to mounting surface)  
PhillipsRound  
Head. Screw  
(4mm x 12mm)  
PhillipsRoundHead  
Screw (4mm x 8mm)  
(Used to mount  
RRU Mounting  
Brackets  
(Used to mount FM MOD  
to mounting surface)  
bracket to RRU)  
4 pc.  
(P/O XM-RCV)  
4 pc.  
(P/O SAT-COM)  
2 pc.  
(P/O XM-RCV)  
4 pcs. each  
(P/O XM-RCV)  
FMModulatorControl  
Interface Wire Harness  
PhillipsRoundHead  
Screw (4mm x 8mm)  
w/ External Tooth Washer  
(Used to mount SCU to mounting  
surface)  
Din Cable, 13- pin  
(6 Meter)  
To connect the RRU to the FM Modula-  
tor / Control Interface  
4 pcs. each  
1 pc.  
(P/O XM-RCV)  
1 pc.  
(P/O XM-RCV)  
(P/O SAT-COM)  
RCAtoRCACable  
(6 Meter)  
To connect the RRU to the FM Modula-  
OPTIONAL  
SUPPLIED  
tor / Control Interface  
ACCESSORIES  
ACCESSORIES  
Owner's  
Manual  
Quick  
Reference  
Card  
Satellite Radio  
Trim Ring,  
Satellite Control  
Model #SAT-PF  
1 pc.  
(P/O XM-RCV)  
Wireless Remote  
Control Model  
#SAT-RC  
Hook & Loop  
AdhesiveTape  
1 cut set.  
(P/O SAT-COM)  
1 pc.  
(P/O SAT-COM)  
1 pc.  
(P/O SAT-COM)  
4
 
TYPICAL FM MODULATED SYSTEM  
INSTALLATION  
6
9
T
2
5
8
0
SF  
1
4
7
R E  
W
P O  
5
 
TYPICALAUXILLARYAUDIOSYSTEM  
INSTALLATION  
3
6
9
T
2
5
8
0
SF  
1
4
7
R E  
W
P O  
6
 
TYPICAL FM MODULATED INSTALLATION for  
SRXM-001 SYSTEM COMPONENT LAYOUT  
Ground (BLACK)  
Attach this wire to the chassis of the car. Be  
sure that the surface is free of paint and is  
not rusty. If a proper ground connection is  
not made, the SRXM-001 System may not  
operate correctly and stray noise may be  
picked up by the unit.  
From Existing  
Vehicle Antenna  
FMRadio  
Satellite Radio  
Antenna  
(Purchased  
Separately)  
SCU  
To FM Radio  
Antenna input  
+12V Battery  
(YELLOW)  
Connect this wire to  
a terminal which is  
always energized.  
FMModulator  
DINCable  
FilterBox  
& Fuses  
RRU  
RCAtoRCA  
Cable  
+12V Accessory / Ignition (RED)  
Connect this wire to a terminal which  
is energized when the ignition switch  
is turned to the "ON" or "ACCESSORY"  
position.  
13-Pin  
DINCable  
Self-Tapping  
PhillipsHead  
Screw  
MOUNTING THE FM MODULATOR  
Install the FM Modulator to the mounting surface with the  
self-tapping screws (4mm x 12mm).  
7
 
SYSTEM INSTALLATION  
RADIORECEIVERUNIT(RRU)  
PROCEDURE for HORIZONTAL INSTALLATION of the RRU  
Attach the mounting brackets to each side of the RRU, using the 4 Phillips Round Head  
Screws (4mm x 8mm).  
1.  
Bracket  
Phillips Head Screws (4mm x  
8mm) used in 4 places  
Determine the mounting location and drill 4x 1/8” (4mm) mounting holes.  
2.  
WARNING  
Never mount the unit near the fuel tank.  
Carpet  
4x 1/8” (4mm)  
mounting holes  
NOTE:If mounting surface is carpeted, use caution when drilling holes to prevent drill bit from  
catching on carpet. Cut holes in carpet before drilling into subsurface.  
Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers and  
LockWashers. UseRTV(siliconesealer)onscrewthreadsoraroundtheholestoprevent  
moistureintrusion.  
3.  
RRU  
Self-tapping Screw  
(5mm x 15mm), w/Flat  
Washers and Lockwashers  
Carpet  
used in 4 places  
Bracket  
8
 
PROCEDURE for VERTICAL INSTALLATION of the RRU  
Attach a mounting bracket to each side of the RRU, using the 4 Phillips Round Head  
Screws (4mm x 8mm).  
1.  
RRU  
Phillips Head Screws (4mm x  
8mm) used in 4 places  
Bracket  
Determine the mounting location and drill 4 x 1/8” (4mm) mounting holes.  
2.  
WARNING  
Never mount the unit near the fuel tank.  
Carpet  
4x 1/8” (4mm)  
mounting holes  
NOTE:Ifmountingsurfaceiscarpeted,usecautionwhendrillingholestopreventdrillbitfrom  
catching on carpet. Cut holes in carpet before drilling into subsurface.  
Mounttheunitinplace,using4Self-tapping Screws(5mmx15mm),w/FlatWashersandLock  
Washers. UseRTV(siliconesealer)onscrewthreadsoraroundtheholestopreventmoisture  
3.  
intrusion.  
RRU  
Self-tapping Screw  
(5mm x 15mm), w/Flat  
Washers and Lockwashers  
used in 4 places  
Carpet  
Bracket  
9
 
PROCEDURE for the MOUNTING of the RRU UNDER THE REAR DECK  
Attach the mounting brackets to each side of the RRU, using the 4 Phillips Round Head  
Screws (4mm x 8mm).  
1.  
Bracket  
Phillips Head Screws  
used in 4 places (4mm x 8mm)  
2.  
Determine the mounting location and drill four 4mm mounting holes.  
Underside of  
Rear Deck  
4x 1/8” (4mm)  
mounting holes  
(4 places)  
Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers and  
Lock Washers.  
3.  
Rear  
Deck  
Self-tapping Screw  
(5mm x 15mm), w/Flat  
Washers and Lockwashers  
used in 4 places  
10  
 
INSTALLINGTHESATELLITESYSTEMCONTROLUNIT(SCU)  
PROCEDURE for a TYPICAL INSTALLATION of the SCU USING HOOK &  
LOOP ADHESIVE TAPE (SUPPLIED)  
1.DeterminewheretheSCUistobelocated(flatsurface)NOTE:Thechosenpositionmustallow  
aclearviewofthedisplayandeasyaccesstothecontrolsforboththeDriverandPassenger  
ofthevehicle.  
2.UsinganAlcoholSwab,cleananddrytheentiresurfaceareawheretheSCUistobemounted  
and the back surface of the SCU.  
3. Remove the protective paper from the back of the first piece of the supplied Hook & Loop  
Adhesive Tape (Loop side) and apply it to the mounting surface (see Figure 1.)  
4.RemovetheprotectivepaperfromthebackofthesecondpieceofthesuppliedHook&Loop  
AdhesiveTape(Hookside)andapplyittothebacksideoftheSCU(seeFigure2.). Position  
theSCUcableintheappropriatedirectionalchannelonthebackoftheSCUsothattheback  
surface is flat (see Figure 3.).  
5. Carefully press the SCU into place.  
Velcro Tape (Loop)  
Hook&LoopAdhesiveTape(Hook)  
Figure 2.  
Figure 1.  
Figure 3.  
NOTE:  
Donotinstalltheunitinthefollowinglocations:  
InLocationsexposedtodirectsunlight.  
Where hot air is discharged from the car heater.  
Inareassubjecttoextremetemperatures.  
11  
 
PROCEDURE FOR A TYPICAL BRACKET INSTALLATION OF THE SCU  
(Bracket not supplied)  
Audiovox suggests this type of installation over the Hook & Loop type of installation though the Hook & Loop  
installation (if done correctly) is a secure and sufficient mounting option. Installation of the SCU using a  
bracket results in a professional, factory-installed look, without visibly damaging the interior of the vehicle.  
When combined with the optional Trim Ring (model #SAT-PF) the results are further cosmetically en-  
hanced. There are several types of brackets available to accomplish this type of installation.  
The installation procedure that follows, illustrates the use of a Pro.Fit® mounting bracket. Audiovox has  
found that the Pro.Fit® VSM® line of mounting brackets are easy to install and compliments the installation  
of the SCU as well as being a perfect match to the optional Trim Ring (model #SAT-PF). Pro.Fit® VSM®  
mounting bracket reduce the installation liability while maintaining the resale value of a car because of the  
professional fit, professional look and safe design.  
Currently Pro.Fit® VSM® offers hundreds of brackets, covering most popular cars, vans, and trucks. Step-  
by-step instructions and technical support are available for every mount and application.  
After the proper mounting bracket has been selected and installed using the Original Manufacturers  
installation instructions, proceed with the following steps:  
1. Feed the SCU Cable through the hole in the Trim Ring (optional) and connect it to the  
RF Modulator.  
2. Using the Phillips Head Screws and the External Tooth Lock Washers (supplied),  
Mount the SCU to the bracket as shown in the Figure below.  
NOTE: Use caution not to over tighten the screws into the back of the SCU as this may  
cause damage to the unit.  
Do not install the unit in the following locations:  
In Locations exposed to direct sunlight. Where hot air is discharged from the car heater. In areas  
subject to extreme temperatures.  
NOTE:  
(Example installation position)  
Phillips Round Head Screw (4mm x 8mm)  
1
4
2
5
3
6
7
8
9
0
SFT  
External Tooth Washer  
(4mm int.)  
Bracket  
(Not Supplied)  
Bracket Shown is a PRO.FIT for ordering information  
SCU  
TrimRing  
(Not Supplied, Model #SAT-PF)  
For ordering information call Audiovox Electronics toll-free telephone assis-  
tance line at 1-800-645-4994 or contact us via the web:  
Upon completion of the SCU installation and before the XM radio is activated a test of the system should be  
performed. To verify that the SRXM-001 system and the antenna have been installed correctly and are  
functioning, select and listen to CH 1. (XM preview channel). If there is no power to the SCU check that all  
connections have been made and that fuses are good. If there is no signal present, make sure that the  
antenna is unobstructed (move vehicle) and check the antenna cable connection to the RF Modulator. For  
a detailed trouble-shooting guide, refer to the Owner’s Manual.  
128-6213A  
© Copyright 2001 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788  
12  
 

2Wirer HDCR 1230G User Manual
3M Model Vehicle 78 8069 3983 7 User Manual
Abocom Network Card PLF100 User Manual
Acoustic Research Speaker System AW827 User Manual
Airlink101 Switch AKVM 2A User Manual
Aiwa Stereo System Z L70 User Manual
American Standard Hot Tub 6030Y2A202XXX User Manual
American Standard Outdoor Shower 7220702 User Manual
ATO Speaker System SCM16A User Manual
Behringer Music Mixer MON800 User Manual