Audiovox Automobile Alarm PRO OE3B4 User Manual

TRANSMITTERPROGRAMMINGGUIDE  
Model:PRO-OE3B4  
The transmitters included with the security system have been pre-programmed  
at the factory, with each button pre-assigned to control a specific function of the  
security system. Although the security system in the vehicle has either a 3 or 4  
channel receiver, depending on the model, the transmitters included with the  
system are capable of transmitting 7 distinct signals. This allows you to program  
each transmitter to more than one vehicle in two car families, and also allows you  
to change which button(s) control certain functions of the system.  
(Example: Transmitter channel 5 can be programmed to activate Receiver  
channel 2.) Refer to the chart below for access to each of the transmitter channels,  
and for the standard factory button assignments.  
TRANSMITTER  
SYSTEM RECEIVER  
CHANNEL BUTTON  
CHANNEL  
FUNCTION  
Remote Arm  
1
1
Remote Emergency Panic  
Remote Door Lock  
Remote Disarm  
2
3
2
3
4
Remote Emergency Panic  
Remote Door Unlock/Unlock 2  
Single Push Pulsed Output for Optional Accessory  
Or Double Push For Additional Optional Accessory  
Single Push Pulsed Output for Optional Accessory  
Or Push And Hold For Extended Output  
4
5
&
&
Single Push Pulsed Output for Optional Accessory  
Or Push And Hold For Extended Output  
5
6
7
&
6
7
RF Channel For Options  
RF Channel For Options  
All 3  
Buttons  
Some of the more common accessories for these additional channels are;  
AS 9554  
AS 9075  
AS 9153  
AS 9256  
Remote Garage Door Interface  
Remote car starter  
Remote window roll up  
Remote trunk release relay  
128-6122  
1 of 4  
Released 8-9-01.  
 
14. Press and release the valet push-button switch once.  
15. The dash LED will flash four times, and the sounding device will beep four  
times, indicating the system is ready to accept programming for receiver's  
channel 4.  
16. Press and hold any button combination as shown on the front cover of this  
guide until the sounding device emits a long beep, indicating the signal has  
been stored into memory.  
17. If you have additional transmitters (up to 4) that need to be programmed,  
repeat step 16 for each transmitter.  
18. Press and release the valet push-button switch once.  
19. The dash LED will flash four times, and the sounding device will beep four  
times, indicating the system is ready to accept programming for receiver's  
channel 5.  
20. Press and hold any unused button combination as shown on the front cover  
ofthisguideuntilthesoundingdeviceemitsalongbeep,indicatingthesignal  
has been stored into memory.  
21. If you have additional transmitters (up to 4) that need to be programmed,  
repeat step 20 for each transmitter.  
22. Turn the ignition key off. The sounding device will emit one short beep  
followedbyonelongbeepindicatingthesystemhasterminatedtheprogram  
mode.  
TRANSMITTERBATTERYREPLACEMENT  
You will notice a decrease in transmitter range as the battery condition  
deteriorates. Transmitter battery replacement is recommended at least every  
10 to 12 months, depending upon how frequently the transmitter is used.  
The transmitter has a small LED visible  
through the case. This LED can be used  
to indicate battery condition. If the LED  
does not illuminate, then the battery is  
discharged, and must be replaced.  
To replace the transmitter battery,  
1. Remove the small phillips head screws  
from the bottom cover of the transmitter.  
2. Carefully unsnap the top cover of the transmitter from the bottom cover.  
3. Remove the discharged battery, making note of the location of the + and -  
contacts, and replace with a new type GP 27A 12 volt battery.  
4. Replacethetransmittercover, takingcarenottodamagetheLEDorswitches  
on the circuit board, and secure with the small phillips head screw.  
128-6122  
3 of 4  
 
ORDER FORM FOR 3 BUTTON TRANSMITTER  
MODEL NO. PRO-OE3B4  
IMPORTANT: To help us expedite your order, please print all of the information legibly,  
and mail this form and your payment according to the instructions below.  
Note: Order Pad # 70 if your Lock & Unlock Icons are White  
Order Pad # 71 if your Lock & Unlock Icons are Red.  
Note: Transmitter model number found on back of case. ___________  
1. Name : ____________________________________________________  
Address: _____________________________________________________  
City : _____________________ State : _______ Zip Code : ____________  
2. Telephone Number : ( _______ ) _______________________________  
3. Enter the total number of transmitters required here : ________________  
4. List model number of your actual transmitter pad as shown on page 4 of this  
manual: _________________________  
5. The cost per transmitter is $ 65.00.  
6. Enter the total amount enclosed here : ____________________________  
(New York State residents must include the appropriate sales tax.)  
7. Method of payment; check one of the boxes below.  
! Mastercard ! Visa ! Check or money order * ( do not send cash )  
* Make checks payable to Audiovox Corporation  
8. Credit Card Number : ________________________________________  
9. Credit Card Expiration Date : _____________________  
Credit card purchasers can order additional or replacement  
transmitters by phone. Simply dial 1 - 800 - 645 - 4994 and follow  
the instructions from the operator interface.  
"
10. Mail this form, and your check, to :  
Audiovox Electronics Corp., 150 Marcus Blvd. Hauppauge, N.Y., 11788  
Attn.:TRANSMITTERDEPARTMENT  
©2001AudiovoxElectronicsCorp., 150MarcusBlvd., Hauppauge, NY, 11788  
128-6122  
128-6122  
4 of 4  
 

AEG Dishwasher 64800 User Manual
AEG Ventilation Hood 8609 D User Manual
Aiphone Intercom System B User Manual
Aiwa Speaker System UZ US301 User Manual
Alpine Automobile Alarm SEA 8081 User Manual
American DJ DJ Equipment Flash Tube Buffer User Manual
Audiovox Car Stereo System ACD85 User Manual
Axis Communications Security Camera M3011 User Manual
BeefEater Charcoal Grill SL4000s User Manual
Behringer Music Pedal DM100 User Manual