Audiovox Automobile Alarm PRO 9232A User Manual

Model PRO 9232a  
OWNER’S MANUAL  
KEYLESS ENTRY ALARM UPGRADE MODULE  
Congratulations on your purchase of the PRO 9232a automotive Keyless Entry  
Upgrade Alarm System. This system is a state - of - the - art auto security system  
that is designed to automatically arm and disarm when it receives a command from  
your existing Factory Keyless Entry Transmitter. Taking a few moments to read this  
manual will help to ensure that your vehicle is protected at all times.  
NOTE:  
The system has the ability to beep the vehicle's horn, sound a siren, or both. Where  
a beep or chirp is mentioned, consider either or both may sound.  
ARMINGTHESYSTEM:(ACTIVE)  
1. Turn the ignition key off, exit the vehicle, and close all doors.  
2. Press and release the Lock button on the keychain transmitter.  
3. The siren and or horn will beep one time, the parking lamps will flash one time,  
and the red dash mounted LED will begin to slowly flash, indicating that the  
system is ARMED.  
If the siren/horn sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.  
Simply close the opened entry point to provide full protection. If the siren "chirped"  
three times, sometime after arming, the exclusive delayed dome light learn circuit  
has been programmed and the system detected a open entry point after the  
learned delay expired. Again, closing the hood, trunk, or doors will correct the  
problem and you do not need to disarm the system to make the correction. If the  
siren/horn did not sound when arming, then the chirps have been turned off, and  
you should refer to the section titled “ ELIMINATING THE ARM / DISARM CHIRPS “  
in this manual.  
4. Any time the door lock switch in the vehicle is used to lock the doors while  
the ignition key is turned off, the system will immediately arm. To lock the doors  
after entering the vehicle, make sure the ignition key is switched on first.  
Turning the ignition key on first will stop the system from arming.  
ARMING THE SYSTEM : ( PASSIVE )  
1. Turn the ignition key off, exit the vehicle, and close all doors.  
2. The dash mounted LED will begin to flash rapidly, indicating that the system  
128-6626  
1 of 8  
 
installed, the vehicle’s interior lights will turn on for 30 seconds, or until the  
ignition key is turned on.  
NOTE: If your system has been programmed for “ passive arming “, then it will  
begin to re-arm immediately after disarming. This is indicated by a  
rapid flashing of the red dash mounted LED Opening one of the  
vehicle’s doors will suspend the passive arming process until all doors  
have been closed, or until the ignition key has been turned on.  
INTRUSION WARNING SIGNALS :  
The system will inform you if an intrusion attempt has occurred while you were away  
from the vehicle. If an intrusion attempt has occurred, the siren and or horn will beep  
four times when the system is disarmed. The vehicle’s parking lights will also flash  
three times to indicate an intrusion has occurred.  
Enter the vehicle and observe the dash mounted LED for further information.  
1. If the LED is flashing one time...pause...one time...pause...etc., then an  
intrusion attempt was made to a voltage sensing, light activated entry point, or  
to an optional sensor that has been connected to zone 1.  
2. If the LED is flashing two times...pause...two times...pause...etc., then an  
intrusion attempt was made to the hood or trunk, or to an optional sensor that  
has been connected to zone 2.  
3. If the LED is flashing three times...pause...three times...pause...etc., then an  
intrusion attempt was made through one of the vehicle’s doors.  
These intrusion warning indicators are stored in the system’s memory, and will  
only be erased when the ignition key is turned to the “ on “ position.  
OPERATINGTHEEMERGENCYPANIC:  
The buttons on your keychain transmitter will allow you to immediately activate the  
alarm in emergency situations. To use the remote panic switch;  
1. Presstheunlock,thenlock,thenunlockbuttonsonyourkeychaintransmitterwithin  
3seconds. Thealarmwillimmediatelysound,andcontinuetosoundfor30seconds.  
2. To stop the alarm before the 30 second cycle has expired, simply press and  
release the unlock button on your keychain transmitter.  
USING THE VALET SWITCH :  
The valet switch allows you to temporarily bypass all alarm functions, eliminating the  
need to hand your transmitter to parking attendants or garage mechanics. When the  
system is in valet mode, all alarm functions are bypassed, however the remote panic  
feature and remote door locks will remain operational. To use the valet mode, the  
system must first be disarmed either by using your keychain transmitter, or  
by activating your personalized manual override code.  
Page 3  
128-6626  
3 of 8  
 
TOENTERTHEVALETMODE:  
1. Disarm the unit by use of the factory transmitter or by use of the manual override  
sequence.  
2. Turn the ignition switch to the “On” position.  
3. Press and hold the valet/override pushbutton switch for 5 seconds. The LED  
turns on, indicating valet mode has been successfully entered.  
TO EXIT VALET:  
With the ignition switch in the on position, press and release the valet/override  
pushbutton switch one time. The LED turns off indicating the valet mode has  
successfullybeenexited.  
MANUALOVERRIDEOPERATION:  
If your factory transmitter is lost, broken, or otherwise rendered inoperable, your  
system can be overridden allowing operation of the vehicle. The manual override  
code is pre-programmed at the factory to 11. This code can be changed by the  
operator to a more familiar two digit number. Once you’ve become familiar with the  
system’s operation and override procedure, we suggest you change the code for  
added security.  
NOTE: The override procedure below describes use, assuming that the factory  
pre-set code has not been changed and is still set to the factory default 11.  
The valet/override push button switch is used to enter the tenths and units  
digits, pressing and releasing this button one time for each digit required.  
To manually override your system, with a code of 11, follow the sequence listed  
below:  
1. The LED is flashing indicating unit is armed, enter the vehicle, the siren will  
sound, turn the ignition switch to the “on” position.  
2. Within 10 seconds begin to enter tenths digit of override code. (In this ex-  
ample the code is 11, so press and release the Valet/Override pushbutton  
one time).  
3. Within 10 seconds of entering the last tenths digit, turn ignition “off then on”.  
4. Within 10 seconds of turning the ignition switch on, begin to enter units digit  
of override code. (In this example the code is 11, so press and release  
the Valet/Override pushbutton one time).  
5. Within 5 seconds after the last units digit is entered, turn the ignition switch  
off, then on, and start your vehicle.  
If the manual override code is entered properly, the unit stops sounding, the LED  
turns off, indicating a successful override. The system is now disarmed and you  
can start and operate your vehicle. The unit will allow three attempts to disarm via  
Page 4  
128-6626  
4 of 8  
 
the manual override sequence. If the code is not successfully entered within the  
three attempts, disarming with the manual override switch will be locked for 10  
minutes.  
In many cases, to increase the security of your system, you may elect to change  
the manual override code to a number that is more familiar to you, or simply to  
have a different code than was pre-assigned from the factory. To Change the pre-  
assigned override code follow the steps outlined below.  
It is advised you read both sections under the headings “Programming Your  
Custom Override Code” and, “Custom Code Programming Example”, To com-  
pletely understand the procedure before beginning:  
Programming Your Custom Override Code:  
Unlike override switches easily found, and defeated, the PRO-9232 allows the  
consumer to program a personal override code, offering a higher level of security.  
The system comes from the factory with a pre-programmed override code of 11. To  
change this default override code, do the following:  
1. Disarm the system by use of the transmitter, or by use of the emergency override  
sequence. Turn the ignition switch to the on position.  
2. Within 10 seconds, press and release the valet/override switch, 3 times.  
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.  
(The siren or horn will beep and the lights will flash one time.)  
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and  
releasing the pushbutton switch from 1 up to 9 times.  
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on.  
6. Within 10 seconds, begin to enter your chosen units digit by pressing and  
releasing the pushbutton switch from 1 up to 9 times.  
7. Finish by turning the ignition switch to the off position.  
If the new code was accepted, the unit will report back the newly entered code, by  
flashing the LED, first indicating the 10ths digit, pause and then the units digit.  
The unit will report the new code three times with a one second pause between  
each code, then the system will begin arming. If the LED flash pattern re-  
ports the previously stored code, the new code was not entered correctly. Please  
repeat steps 1 through 7 above considering the following.  
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize  
a0 (Zero), or no digit entered in any place, units or tenths.  
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for  
more then 5 seconds during any of the above steps, the unit will revert back  
to the last successfully stored code.  
Page 5  
128-6626  
5 of 8  
 
Custom Code Programming Example:  
To Change the code from the factory pre-assigned code of 11 to “52” you would do  
the following:  
1. Disarm the system by use of the transmitter, or by use of the emergency  
override sequence.  
2. Turn the ignition switch to the on position.  
3. Within 10 seconds, press and release the valet/override switch, 3 times.  
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.  
(The siren or horn will beep and the lights will flash one time.)  
5. Within 10 seconds, begin to press and release the push button switch to set the  
tenths digit.  
(As per the example, press and release 5 times to set the tenths digit to 5)  
6. Within 10 seconds of the last press of the push-button, turn the ignition switch off  
then on.  
7. Within 10 seconds, begin to press and release the push button switch to set the  
units digit.  
(As per the example, press and release 2 times to set the units digit to 2).  
8. Turn the ignition switch to the off position. Immediately observe the L.E.D. flash  
pattern.  
You will note the LED flashing five times, pause, and then flash two times, pause.  
This pattern will be repeated three times indicating the new code (52) has been  
accepted and stored in memory.  
NOTE: If after step 7, the LED flashes a code other than what was just entered, this  
indicates that the code has not been changed. You will have to repeat  
steps 1 through 7 above being certain to note the following:  
Acceptable digits 10ths or units are 1 through 9. The unit will not recog-  
nize a 0 (Zero), or no digit entered in any place, units or tenths.  
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for  
more then 5 seconds during any of the above steps, the unit will revert back  
to the last successfully stored code.  
ADDITIONALREMOTEFUNCTION:  
This system allows the control of any one of the following optional accessories;  
Remote Car Starter  
Remote Window Closure  
Remote Window Open  
Page 6  
128-6626  
6 of 8  
 
To operate the optional accessory;  
1. Press the lock, then unlock, then lock buttons on your keychain transmitter within  
3 seconds.  
2. The optional accessory will immediately activate.  
OPTIONALAUTOLOCK/UNLOCKFEATURE:  
If your existing factory installed keyless entry system did not include the automatic  
door lock and unlock feature, then this feature can be activated from the PRO 9232  
upgrade module. When this accessory has been added, any time the ignition key  
is turned to the on position and all vehicle doors are closed, the doors will lock in  
4seconds. Additionally,anytimetheignitionkeyisturnedtotheoffposition,thedoors  
will unlock.  
ELIMINATINGTHEARM/DISARMCHIRPS:  
The normal arming and disarming confirmation chirps can easily be turned off using  
the valet pushbutton switch. To do this;  
1. Turn the ignition key on, and then off.  
2. Within10secondsofturningtheignitionkeyoff,pressandreleasethe valet switch  
3 times.  
3. a. If, before proceeding with step 1, the chirps were on, then you will hear 2 chirps  
to indicate that the chirps have been turned off.  
b. If, before proceeding with step 1, the chirps were off, then you will hear 1 chirp  
to indicate that the chirps have been turned on.  
4. Wheneverpowertothesystemhasbeendisconnected(forrepairorservicetothe  
vehicle ), the chirps will be activated when the power is re - connected. To turn the  
chirps off, simply execute steps 1 through 3 above.  
NOTE : Whenever the Arm/Disarm chirps are by-passed, the 3 chirp defective  
zoneandthe4chirpintrusionindicatorwillalwaysoperate.Thisfeature  
willalwayswarnyouifadoorwasleftajarwhenarming,orthevehiclewas  
tampered with in your absence.  
Page 7  
128-6626  
7 of 8  
 
PRO 9232a  
SYSTEM FUNCTIONS AT A GLANCE  
DASH L.E.D. INDICATORS  
RAPID FLASHING ..........................................................  
PASSIVE ARMING  
SLOW FLASHING ...........................................................................  
ARMED  
DISARMED  
VALET MODE  
OFF ...........................................................................................  
ON - SOLID ............................................................................  
3 FLASH ... PAUSE .....................................................  
2 FLASH ... PAUSE .....................................................  
1 FLASH ... PAUSE .....................................................  
INTRUSION ZONE 3  
INTRUSION ZONE 2  
INTRUSION ZONE 1  
CHIRP INDICATORS  
1 CHIRP * ............................................................................................  
2 CHIRPS* .....................................................................................  
ARM  
DISARM  
3 CHIRPS ...................................................................  
3 CHIRPS .......................................  
10 MIN. PASSIVE ARM / DOOR OPEN  
ARM / DOOR OPEN  
4 CHIRPS .................................................................  
DISARM / INTRUSION  
DISARM / AFTER 10 MIN.  
PASSIVE ARM  
2 SHORT CHIRPS - 1 LONG CHIRP.....................  
4 SHORT CHIRPS - 1 LONG ................................  
DISARM / AFTER 10 MIN.  
PASSIVE ARM AND INTRUSION  
* These chirps are optional, and can be de-activated.  
PARKING LAMPS  
1 FLASH ..................................................................................................  
ARM  
DISARM  
2 FLASH .........................................................................................  
DISARM / INTRUSION  
3 FLASH ...................................................................  
Your System Has These Features Activated:  
Starter Disable When Armed  
PassiveArming  
InstantTrigger  
RemoteCarStarter  
RemoteWindowOpen  
RemoteWindowClosure  
Key Activated Auto Lock/Unlock  
Shock Detector  
VehicleHorn  
Hardwire  
G
G
G
G
G
G
G
G
G
G
© 2003 udiovox Electronicc Corp. 150 Marcus Blvd. Hauppauge, N.Y. 11788  
FormNo. 128-6626  
128-6626  
8 of 8  
 

Actiontec electronic Network Router GT701D User Manual
Aiphone Speaker IER 2 User Manual
Aiwa CD Player CSD TD52 User Manual
Algolith Stereo Receiver FRS 1002 MD
Alpine Car Stereo System KD A815 User Manual
Alpine Car Video System IVA D310 User Manual
Aluratek Computer Drive AUHR200 User Manual
Amerec Stove PKLE 181 User Manual
American Standard Plumbing Product 2555602 User Manual
BC Speakers Speaker 18 PZB 46 User Manual