Audiovox Automobile Alarm AXT800 User Manual

Model APS-800  
Owner’s Manual  
4 Button Remote Security System  
with Dual Stage Shock Sensor  
IMPORTANT ! In order to provide you with the highest level of security to your vehicle, this  
system is equipped with selectable manual override circuitry. It is possible that you will need  
to override you security system if the transmitter becomes lost, or inoperative due to battery  
failure. Reading the sections on "Manually Overriding Your System" is necessary to fully  
understand the procedure required to enable your vehicle in such situations. In addition, the  
chart on the last page of this manual has a section for the particular features and options  
installed in your vehicle as well as the override method selected. Although the default mode  
is "Valet Switch" operation, the system can be configured for "Custom Code" operation for  
enhanced security. Confirm the override mode selected on the last page of this manual, and  
familiarize yourself with the section on it's operation.  
FEATURES :  
w 2 Four Button S.A.W. Anti-Code Grabbing Transmitters  
w Six Channel Code Learning Programmable Receiver  
w External Superheterodyne Receiver Antenna  
w Single Or Two User Programmable W/Separate Control Outputs  
w Single Button Lock/Unlock or Separate Button Lock/Unlock or Both  
w Single Step Unlock Or Two Step Unlock  
w New Enhanced Panic Feature (Any button other than unlock stops siren, no change to the units state)  
w Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )  
w Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect Off, City Mode)  
w Safe Start Output Controlled From Channel 3 (Option Channel 3 For Trunk, Or For R/S)  
w Remote Panic In All Modes (Press & Hold Lock/Unlock Button For 3 Seconds To Engage)  
w Improved Custom Code Override, User Selectable and Programmable  
w Protected Push Button Valet/Override Switch  
w 7 Function LED  
w Intrusion Alert With Memory  
w Instant Siren Activation  
w Starter Disable Output  
w Additional Engine Immobilizer Output, (Optional Relay Required)  
w True Last Door Arming (Hardwire Only)  
w Defective Zone By-Pass  
w Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared)  
w 6 Tone Mini Siren  
w Car Horn Output For Additional Alarm Response (Improved Timing To Minimize RF Interference.)  
w Additional Negative Trigger Input (Hood & Trunk)  
w RF Inhibit With Ignition On  
w Parking Light Flasher (Relay On Board)  
w Plug In Dual Stage Shock Sensor (Pre-detect, Full Trigger, and “City Mode”)  
w Audible Arm, Disarm, Defect, And Tamper Chirp Indications  
w Headlight Control Output  
w Illuminated Entry Control Output  
OPTIONS :  
w Remote Trunk Release (must have electronic trunk release)  
w Remote Keyless Entry (must have power door locks)  
w Multiple Vehicle Capable  
w Remote Starter  
w Remote Power Window Roll Up  
w Remote Garage Door Interface  
 
NOTE: If the optional Headlamp illumination feature has been added, and has been selected  
for operation when arming, as an added convenience, the system will turn on the  
headlights when the system is armed.  
ARMING THE SYSTEM - PASSIVE ( AUTOMATIC )  
1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid, and trunk lid.  
þ The dash mounted LED begins to flash rapidly, indicating 30 second passive  
arming has begun.  
2. Opening any protected entry point during the 30 second passive arming cycle will immedi-  
ately suspend automatic arming, and the 30 second passive arming cycle will re start when  
all doors are closed. At the end of the passive arming cycle:  
þ The dash mounted LED begins to flash slowly.  
þ Parking Lights flash one time.  
þ Siren sounds one chirp  
If the siren did not sound when arming, then the chirps have been turned  
off, and you should refer to the section titled “ELIMINATING THE ARM /  
DISARM CHIRPS“ in this manual.  
o Doors Lock - Optional  
Door locking during passive arming is a selectable feature.The alarm can  
be programmed to allow the doors to lock only when arming using the  
keychain transmitter, and they will not automatically lock during passive  
arming.  
PROTECTION WHILE THE SYSTEM IS ARMED  
þ Opening any protected door, hood, or trunk lid will cause the alarm to immediately  
sound.The alarm will continue to sound for 30 seconds, then stop and continue to  
monitor all protected entry points. If the thief left a door opened, the alarm will sound  
for six 30 second cycles, remain armed and ignore that triggered zone.  
þ Whenever the system is armed, the red dash mounted LED indicator will slowly flash.  
This serves as a visual deterrent to the potential thief. The LED is a very low current  
bulb, and will not cause the vehicle’s battery to drain, even when left unattended for  
extended periods.  
þ Whenever the system is triggered, the vehicle’s parking lights will flash for the full 30  
second alarm cycle, attracting visual attention to the vehicle.  
þ Optional - Whenever the system is armed, the vehicle’s starting circuit will be by-  
passed. If the thief should choose to ignore the siren, the vehicle can not be started.  
þ Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of  
warning tones.  
þ Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30  
second alarm cycle.  
NOTE: If the optional interior illumination circuit was installed, the interior light will flash as  
well for the full 30 second alarm cycle.  
DISARMING THE SYSTEM  
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button  
is activated, the drivers door only will unlock, pressing the unlock button a second time  
will cause all doors to unlock.  
NOTE: If your transmitter has been configured with single button Lock/Unlock as shown, to  
activate the all door unlock feature operate the Lock/Unlock button a second time  
within 3 seconds of the first unlock command.  
Page 3  
 
1. As you approach the vehicle, press and release the Unlock/Disarm button on the  
keychain transmitter.  
þ The dash mounted LED turns off.  
The LED will start flashing rapidly, indicating that the system is re-arming  
automatically. Open any door to suspend the automatic arming.  
þ Parking Lights flash two times.  
If the parking lights flashed three times, then the alarm was triggered in  
your absence. Before turning the key on, examine the LED to identify  
which zone was triggered.  
þ Siren sounds two chirps.  
If the siren sounds 4 chirps, then the alarm was triggered in your  
absence. Before turning the key on, examine the LED and refer to the  
INTRUSION WARNING SIGNALS section of this manual to identify  
which zone was triggered.  
If the siren did not sound when disarming, then the chirps have been  
turned off, and you should refer to the section titled “ ELIMINATING  
THE ARM / DISARM CHIRPS “ in this manual.  
o Doors Unlock - Optional  
o 2 Step Doors Unlock - Optional  
NOTE: If the optional Headlamp illumination feature has been added, and has been selected  
for operation when disarming, as an added convenience, the system will turn on the  
headlights when the system is disarmed.  
SILENT DISARMING (Must be activated during programming)  
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter  
button is activated, the drivers door only will unlock, pressing the unlock button a  
second time will cause all doors to unlock.  
NOTE: If your transmitter has been configured with single button Lock/Unlock as shown, to  
activate the all door unlock feature operate the Lock/Unlock button a second time  
within 3 seconds of the first unlock command.  
1. Press and hold button the Unlock/Disarm button on the keychain transmitter for 2 seconds.  
þ The dash mounted LED turns off.  
The LED will start flashing rapidly, indicating that the system is re-arming  
automatically. Open any door to suspend the automatic arming.  
þ Parking Lights flash two times.  
If the parking lights flashed three times, then the alarm was triggered in  
your absence. Before turning the key on, examine the LED to identify  
which zone was triggered.  
þ Siren will not sound.  
If the siren sounds 4 chirps, then the alarm was triggered in your  
absence. Before turning the key on, examine the LED and refer to the  
INTRUSION WARNING SIGNALS section of this manual to identify  
which zone was triggered.  
o Doors Unlock - Optional  
o 2 Step Doors Unlock - Optional  
Page 4  
 
NOTE: If the optional headlamp illumination feature has been added, and has been selected  
for operation when disarming, as an added convenience, the system will turn on the  
headlights when the system is disarmed.  
WHILE THE SYSTEM IS SOUNDING  
If during a triggered state, you wish to shut off the siren without disarming your security  
system, simply press and release any transmitter button other than the Unlock/Disarm button.  
This action will turn off the siren yet leave the vehicle fully armed and protected. This feature  
is particularly useful if you are aware of children playing near your vehicle that may acci-  
dently trigger your security system. In this case you can cancel the siren sounding without  
disarming your alarm.  
INTRUSION WARNING SIGNALS  
This system will inform you if an intrusion attempt has occurred while you were away from the  
vehicle. If an intrusion attempt has occurred, the siren will chirp 4 times and the parking lights  
will flash 3 times when disarming the system. Enter the vehicle, and observe the red dash  
mounted LED to identify which zone was triggered.  
Œ If the LED is flashing one time...pause...one time...pause...etc., then an intrusion  
attempt was made to the shock sensor, or an accessory triggering device that may  
have been added to the system.  
 If the LED is flashing two times...pause...two times...pause...etc., then an intrusion  
attempt was made to a hood or trunk pin switch that was added to the system, or to  
a light activated entry point if the alarm was installed using the voltage sensing  
feature.  
Ž If the LED is flashing three times...pause...three times...pause...etc., then an  
intrusion attempt was made through one of the vehicle’s doors.  
These intrusion warning indicators are stored in the system’s memory, and will only be  
erased when the ignition key is turned on.  
VALET SWITCH  
The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to  
hand your transmitter to parking attendants or garage mechanics. When the system is in valet  
mode, all alarm functions are bypassed, however the remote panic feature and remote door  
locks will remain operational. In addition, the parking lights will flash to indicate locking and  
unlocking. To use the valet mode, the system must first be disarmed either by using your  
keychain transmitter, or by activating your personalized manual override code.  
1. Enter the vehicle, and turn the ignition key to the on position.  
2. Press and hold the valet pushbutton switch until the dash mounted LED turns on  
solid. The system will remain in the valet mode.  
3. To return to normal operation, press and release the pushbutton switch any time  
the ignition is on.  
NOTE: Always remember to return the system to normal operation. This will ensure that the  
vehicle remains protected at all times.  
MANUALLY OVERRIDING YOUR SYSTEM:  
USING THE VALET SWITCH MANUAL OVERRIDE  
Your Security System can be disarmed without the use of the keychain transmitter. This is  
Page 5  
 
necessary, since you will need the ability to operate your vehicle if the transmitter is lost or  
its battery fails. If your system has been selected for Valet Switch manual override as  
indicated on the last page of this manual, to by-pass the alarm system;  
1. Open the vehicle door. The alarm will sound.  
2. Turn the ignition key to the on position.  
3. Within 5 seconds, press and release the valet pushbutton switch.  
The alarm system will stop sounding and enter the (by-passed) mode. You can now start  
and operate the vehicle normally.  
Typically this override mode is used only if the transmitter has become inoperative.  
Programming Your Custom Override Code:  
Unlike override switches easily found, and defeated, this security system allows the con-  
sumer to program a personal override code, offering a higher level of security. To take  
advantage of this option, programmable feature # 10 must be selected for the Custom Code  
Option. Consult your installation center for programming details. The system comes from the  
factory with a pre-programmed override code of 11. To change this default override code,  
do the following:  
1. Disarm the system by use of the transmitter, or by use of the emergency override  
sequence. Turn the ignition switch to the on position.  
2. Within 10 seconds, press and release the valet/override switch, 3 times.  
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.  
(The siren or horn will beep and the lights will flash one time.)  
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing the  
pushbutton switch from 1up to 9 times.  
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on.  
6. Within 10 seconds, begin to enter your chosen units digit by pressing and releasing the  
pushbutton switch from 1 up to 9 times.  
7. Finish by turning the ignition switch to the off position.  
If the new code was accepted, the unit will report back the newly entered code, by flashing  
the LED, first indicating the 10ths digit, pause and then the units digit. The unit will report the  
new code three times with a one second pause between each code, then the system will  
begin arming. If the LED flash pattern  
reports the previously stored code, the new code was not entered correctly. Please repeat  
steps 1 through 7 above considering the following.  
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0  
(Zero), or no digit entered in any place, units or tenths.  
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5  
seconds during any of the above steps, the unit will revert back to the last  
successfully stored code.  
Custom Code Programming Example:  
To Change the code from the factory pre-assigned code of 11 to “52” you would do the  
following:  
1. Disarm the system by use of the transmitter, or by use of the emergency override  
sequence.  
2. Turn the ignition switch to the on position.  
3. Within 10 seconds, press and release the valet/override switch, 3 times.  
Page 6  
 
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.  
(The siren or horn will beep and the lights will flash one time.)  
5. Within 10 seconds, begin to press and release the push button switch to set the tenths  
digit.  
(As per the example, press and release 5 times to set the tenths digit to 5)  
6. Within 10 seconds of the last press of the push-button, turn the ignition switch off then on.  
7. Within 10 seconds, begin to press and release the push button switch to set the units digit.  
(As per the example, press and release 2 times to set the units digit to 2).  
8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern.  
You will note the LED flashing five times, pause, and then flash two times, pause. This  
pattern will be repeated three times indicating the new code (52) has been accepted and  
stored in memory.  
NOTE: If after step 7, the LED flashes a code other than what was just entered, this  
indicates that the code has not been changed. You will have to repeat steps 1  
through 7 above being certain to note the following:  
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no  
digit entered in any place, units or tenths.  
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5  
seconds during any of the above steps, the unit will revert back to the last successfully  
stored code.  
MANUALLY OVERRIDING YOUR SYSTEM:  
USING THE CUSTOM CODE OVERRIDE  
Assuming the override code programmed has not been changed, and the default override  
code of 11 is in the system's memory.  
1) Enter the vehicle and turn the ignition switch to the on position.  
NOTE: The siren will sound.  
2) Within 5 seconds, press and release the pushbutton switch 1 time.  
3) Within 5 seconds, turn the ignition switch off then on.  
4) Within 5 seconds, press and release the pushbutton switch 1 time.  
5) Turn the ignition switch off then on and start the vehicle.  
NOTE: If you have changed the programmed override code then substitute your new code  
tenths for step 2 above, and units for step 5 above.  
ELIMINATING THE NORMAL ARM / DISARM CHIRPS  
As explained earlier in the manual, you can eliminate the chirps selectively any time you arm  
or disarm the system simply by holding the ARM or DISARM button for two seconds. If you  
find the normal arming and disarming chirps annoying, they can be turned off permanently,  
eliminating the need to hold the ARM / DISARM button for two seconds. To do this,  
1. Turn the ignition key on then off.  
2. Within 10 seconds, press and release valet switch three times.  
3. If the chirps were on before you started, then you will hear 2 chirps indicating they have  
been turned off.  
If the chirps were off before you started, then you will hear one chirp indicating they have been  
turned on.  
Page 7  
 
NOTE: Whenever the chirps are by - passed, the 4 chirp intrusion indicator and 3 chirp  
defective zone indicator will always operate. Since these are important warnings to  
you that something has happened, they cannot be eliminated.  
REMOTE PANIC OPERATION  
The Lock or Unlock button on your keychain transmitter also functions as a panic switch for  
use in emergency situations. To use remote panic,  
1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more  
seconds. The alarm will immediately sound.  
2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter again for  
3 seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds.  
Also if any transmitter button other than the Lock or Unlock button is pressed and  
released, the Panic mode will be turned off immediately. The normal function of this  
transmitter button will be suspended during the Panic sounding period.  
3. During the panic mode, the Lock and Unlock buttons can be used to lock and unlock the  
doors, (if the option is installed), however once the unlock/disarm button is pressed, the  
vehicle's starter inhibit device, (where installed) will be disabled allowing the vehicle to  
start.  
NOTE: While in the Panic mode, pressing and releasing the Lock or Unlock buttons will, if  
the option is installed, lock and unlock the doors respectively. While in the panic  
mode, anytime the Unlock button is pressed, the panic feature will continue for the  
allotted 30 seconds, however, the security system will be disarmed allowing the  
vehicle to start.  
R.F. SHOCK SENSOR MODE SELECTION  
The way in which your alarm system reacts to threatening vibrations, created by attempts to  
enter the vehicle by breaking a window, is adjustable by the transmitter immediately after  
arming. There are 4 modes of operation that can be selected by the operator.  
1: Normal Operation (default mode)  
In this mode, any strong vibrations will cause the siren to sound (full detect) for 30 seconds.  
Any lesser vibration will cause the siren to emit about 6 short warn away chirps, (pre-detect).  
2: Stage 1 (Omit pre-detect)  
In this mode, the warn away chirps created by the lesser vibration will be deleted. If strong  
vibration occurs, the siren will sound.  
3: Stage 2 (Omit pre & full detect)  
In this mode, both the pre-detect stage, and the full trigger stage of the sensor are defeated.  
The unit will not react to vibration of any magnitude.  
4: Stage 3 (City Mode)  
In this mode, the pre-detect chirps will change from 6 pre-warning tones to a full 10 seconds  
of warning chirps.  
The full detect trigger duration will be reduced from 30 second to 15 second.  
NOTE: Setting the stage of the shock sensor will be effective for one arming cycle only.  
Once the system has been disarmed, the very next arming cycle will cause the sensor to  
default to the normal operation stage.  
To change or adjust the shock sensor:  
1) Press and release the ARM button of you keychain transmitter.  
a) Within 2 seconds of arming, press and release the ARM button 1 time, to defeat the  
pre-detect stage of the shock sensor. (The lights will flash and the siren will chirp 1 time)  
Page 8  
 
b) Within 2 seconds of step 1, press and release the ARM button 2 times, to defeat the pre  
and full detect stages of the shock sensor. (The lights will flash and the siren will  
chirp 2 times)  
c) Within 2 seconds of step 1, press and release the ARM button 3 times to enter the "City  
Mode" of operation. (The lights will flash and the siren will chirp 3 times)  
OPTIONAL DEVICE OUTPUT ( CHANNEL 3 )  
Controlled By: o Trunk/Key Button o Option Button o Lock + Unlock Buttons o Lock +  
Trunk/Key Buttons o Lock + Option Buttons o Unlock + Trunk/Key Buttons o Unlock +  
Option Buttons o Trunk/Key + Option Buttons  
Other Transmitter button configurations are also available. Consult your installation center  
for other configurations not listed above that may have been programmed to operate a  
specific feature of your system.  
This security system is equipped with an output which will activate when the appropriate  
transmitter button is depressed for 4 seconds. Optional devices that may be connected to  
this channel are;  
o Remote Electric Trunk Release  
o Remote Car Starter  
o Remote Window Closure  
o Remote Garage Door Interface  
NOTE: In addition there may be a second optional feature connected to your system that  
when the same transmitter button is pressed and released 2 times within 3 seconds  
(double pressed), the second optional feature will activate. This output is typically  
used for a remote start option and will likely prevent inadvertent activation of the  
remote start device if young children are playing with the hand held transmitter.  
If your vehicle is not equipped with an electronic trunk release switch, or other option listed,  
this feature may have been connected to another accessory. Please ask your dealer for  
further information.  
ADDITIONAL REMOTE FUNCTION ( CHANNEL 4 )  
Controlled By: o Trunk/Key Button o Option Button o Lock + Unlock Buttons o Lock +  
Trunk/Key Buttons o Lock + Option Buttons o Unlock + Trunk/Key Buttons o Unlock +  
Option Buttons o Trunk/Key + Option Buttons  
Other Transmitter button configurations are also available. Consult your installation center  
for other configurations not listed above that may have been programmed to operate a  
specific feature of your system.  
This security system has an additional feature that can be connected to a number of differ-  
ent optional accessories. Some of the more common uses for this channel are:  
o Remote Car Starter  
o Remote Window Closure  
o Remote Garage Door Interface  
To remotely operate the device indicated, momentarily press, or press and hold the  
appropriate transmitter button(s) as indicated above.  
ADDITIONAL REMOTE FUNCTION ( CHANNEL 5 )  
Controlled By: o Trunk/Key Button o Option Button o Lock + Unlock Buttons o Lock +  
Trunk/Key Buttons o Lock + Option Buttons o Unlock + Trunk/Key Buttons o Unlock +  
Page 9  
 
Option Buttons o Trunk/Key + Option Buttons  
Other Transmitter button configurations are also available. Consult your installation center  
for other configurations not listed above that may have been programmed to operate a  
specific feature of your system.  
This security system has an additional feature that can be connected to a number of  
different optional accessories. Some of the more common uses for this channel are:  
o Remote Car Starter  
o Remote Window Closure  
o Remote Garage Door Interface  
To remotely operate the device indicated, momentarily press, or press and hold the  
appropriate transmitter button(s) as indicated above.  
ADDITIONAL REMOTE FUNCTION ( CHANNEL 6 )  
Channel 6 is an alternate output that can be controlled by the unlock button of the transmitter,  
or by and independent button or combination of buttons. For your vehicle this output is  
Controlled By: o Trunk/Key Button o Option Button o Lock + Unlock Buttons o Lock +  
Trunk/Key Buttons o Lock + Option Buttons o Unlock + Trunk/Key Buttons o Unlock +  
Option Buttons o Trunk/Key + Option Buttons  
Other Transmitter button configurations are also available. Consult your installation center  
for other configurations not listed above that may have been programmed to operate a  
specific feature of your system.  
This security system has an additional feature that can be connected to a number of differ-  
ent optional accessories. Some of the more common uses for this channel are:  
o Remote Car Starter  
o Remote Window Closure  
o Remote Garage Door Interface  
To remotely operate the device indicated, momentarily press, or press and hold the  
appropriate transmitter button(s) as indicated above.  
ADDITIONAL REMOTE FUNCTION (CHANNEL 7)  
Channel 7 is an alternate output that can be controlled by the unlock button of the transmitter,  
or by and independent button or combination of buttons. For your vehicle this output is  
Controlled By: o Trunk/Key Button o Option Button o Lock + Unlock Buttons o Lock +  
Trunk/Key Buttons o Lock + Option Buttons o Unlock + Trunk/Key Buttons o Unlock +  
Option Buttons o Trunk/Key + Option Buttons  
Other Transmitter button configurations are also available. Consult your installation center  
for other configurations not listed above that may have been programmed to operate a  
specific feature of your system.  
This security system has an additional feature that can be connected to a number of  
different optional accessories. Some of the more common uses for this channel are;  
o Remote Car Starter  
o Remote Window Closure  
o Remote Garage Door Interface  
To remotely operate the device indicated, momentarily press, or press and hold the  
appropriate transmitter button(s) as indicated above.  
Page 10  
 
APS 800  
SYSTEM FUNCTIONS AT A GLANCE  
DASH LED INDICATORS  
RAPID FLASHING =  
SLOW FLASHING =  
PASSIVE ARMING/ACTIVE REARMING  
ARMED  
OFF  
=
=
DISARMED  
ON SOLID  
VALET MODE  
3 FLASH...PAUSE =  
2 FLASH...PAUSE =  
1 FLASH...PAUSE =  
INTRUSION ZONE 3  
INTRUSION ZONE 2  
INTRUSION ZONE 1  
SIREN CHIRP INDICATORS  
1 CHIRP *  
=
=
=
=
ARM  
2 CHIRPS *  
3 CHIRPS  
4 CHIRPS  
DISARM  
ARM / DOOR OPENED  
DISARM / INTRUSION  
* These chirps are optional, and can be de - activated.  
PARKING LAMP INDICATORS  
1 FLASH  
=
=
=
ARM  
2 FLASHES  
3 FLASHES  
DISARM  
DISARM / INTRUSION  
Your System Has These Features Activated  
o Starter Disable  
o Remote Keyless Entry  
o Auto Lock with ignition key  
o Auto Unlock with ignition key  
o Passive Arming  
o No Lock in passive mode  
o Hardwire doors, hood, and trunk  
o Custom Code Override  
o Valet Switch Override  
Page 11  
 
© 2001 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788  
128-5882C  
 

Abocom Network Card M73 APO08 420 User Manual
AEG Double Oven D8800 4 User Manual
AEG Freezer S83200CMW0 User Manual
AEG Washer L 87480 FL User Manual
Alpine Car Video System IVE W535HD User Manual
AMX Network Card RDA CKM User Manual
Axis Communications Security Camera P3343 User Manual
Axis Communications Webcam M7011 User Manual
BC Speakers Speaker 12 PS 32 User Manual
Behringer Speaker System EX2200 User Manual